manualshive.com logo in svg

Diamond SmartLyte Plus, Service Manual

Share
Download
Diamond SmartLyte Plus Service Manual Download Page 34

1 Introduction

 

ECO 9099 SOP05-5090F Rev.00 Effective Date: 12/20/18  Page 34 of 58 

 

 

1.3.1.11.  Printer Assembly (CN-A4060) 

The printer is a graphics printer mounted to a board which is connected directly to the CPU 

board. It uses thermal paper, 

AV-BP5025D

. 

It is important to follow the instructions below to avoid damage to the printer or CPU board. 

 

Figure 1-48 Graphic Printer  

1.  Ensure the power to the instrument is off before removing the printer. 

2.  Open the Main Door so that the printer compartment is fully exposed. 

3.  Partially slide the paper tray out  

4.  Tear the paper roll from the printer and completely remove the paper roll and the paper tray. 

Do not pull the paper from the printer as this can damage the printer. 

5.  To remove paper from the printer, press the feed button. 

6.  Slide fingers under the printer green board along the side  to the back until an opening is 

detected. 

7.  Holding by the opening, pull the printer towards you along the printer board guides on the 

analyzer until the printer is disengaged from the CPU board 

8.  Then remove the assembly from the front of the analyzer.  

 

Printer Board 

Guides 

Printer Paper 

Tray 

Printer Paper  

Printer Paper 

Feed Button 

Summary of Contents for SmartLyte Plus



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands