manualshive.com logo in svg

Diamond SmartLyte Plus, Service Manual

Share
Download
Diamond SmartLyte Plus Service Manual Download Page 36

1 Introduction

 

ECO 9099 SOP05-5090F Rev.00 Effective Date: 12/20/18  Page 36 of 58 

 

1.3.1.12.  RFID Board (CN-A4054)

 

The RFID board is attached to the CPU board at JP10. (

Figure 1-29

 CPU Board, Front)   

The RFID board can be accessed after removal of the CPU board as described in 

Section 

1.3.1.5

. 

This board must be connected all the time to the CPU board for proper functioning of the 

instrument.  

DO NOT unplug the RFID board while the CPU board is powered ON. Irreparable damage may 

occur. 

         

 

Figure 1-51 RFID Board  

1.3.1.13.  Valve Board (CN-A4018)  

Valve board has multiple connections to devices on a single platform. The Aspiration Assembly, 

Solenoid Valves, Peri-Pump Motor, all plug into the valve board. The lamp that lights the 

measurement pathway is also located on this board. To access the board; 

1.  The Rear Panel and CPU with RFID boards, described in 

Section 1.3.1.2

 must be removed. 

2.   Remove one screw  with  washer  on the right side which holds  the board in place. (Figure 

4.36 below) 

3.  Then  remove the  seven  electrical connectors,  aspiration, solenoid valves, pump motor,  to 

slide this board out. 

RFID 

Antenna 

RFID 

Components 

Connector to 

CPU Board 

Summary of Contents for SmartLyte Plus



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands