DentalEZ Aeras Ramvac C11 User Manual Download Page 65

Page: 65 / 77

COMPRESSOR USER MANUAL

866-DTE-INFO
dentalez.com
PN: 7717-004A

INSPECT DRYER

Run compressor until tank pressure of at least
45 PSI/310 kPa shows on the Home screen of the
control panel LCD display

(FIGURE 74)

2. On the Technical screen, press and enable

MAINTENANCE MODE (FIGURE 75)

NOTE:

Turning ON maintenance mode disables

remote switching and puts the system in STANDBY
mode.

3. Carefully open the tank petcock

(FIGURE 76)

4. If no water drains from the tank when the valve is

opened, the dryer is working; proceed to step 6.

5. If water drains from the tank when the valve is opened,

the dryer is not working, contact Ramvac at 866-DTE-
INFO.

MAINTENANCE (CONTINUED)

SECTION V - CARE

TANK

PETCOCK

FIGURE 76. OPEN TANK PETCOCK

FIGURE 74. RUN COMPRESSOR TO 45 PSI/310 KPA

07:33:14 PM

LTE

Settings

Technical

Info

Home

20 hrs

Equipment Runtime

70.3 F

Ambient Temp

-40.0 F

Pressure Dew Point

45 PSI

Tank Pressure

FIGURE 75. ENABLE MAINTENANCE MODE

Service

Runtimes

Sensors

Motors

Alerts

High Pressure Mode

Maintenance Mode

07:33:14 PM

Maintenance Mode

LTE

Settings

Technical

Info

Home

Network

(Continued on the next page.)

Summary of Contents for Aeras Ramvac C11














































































Search results

Summary of Contents for Aeras Ramvac C11

Reviews:

Related manuals for Aeras Ramvac C11

Brands by name

Popular brands

DentalEZ Aeras Ramvac C11, User Manual

Search results

Summary of Contents for Aeras Ramvac C11

Reviews:

Related manuals for Aeras Ramvac C11

Brands by name

Popular brands