DentalEZ Aeras Ramvac C11 User Manual Download Page 59

Page: 59 / 77

COMPRESSOR USER MANUAL

866-DTE-INFO
dentalez.com
PN: 7717-004A

REPLACE INTAKE FILTER

NOTE: All compressor models use the same intake filter.

TOOLS REQUIRED



Torx 25 Screwdriver

On the control panel LCD display, go to the Technical
screen. Press

MAINTENANCE MODE (FIGURE 53)

NOTE:

Turning on maintenance mode disables remote

switching and puts the system in standby mode.

2. Remove intake filter cap by removing two screws

(FIGURE 54A)

3. Remove intake filter and discard

(FIGURE 54B)

4. Install replacement intake filter and replace intake filter

cap.

5. On the Technical screen, press

SERVICE >

(FIGURE 55)

6. On the Service screen, press

FILTER PACK

(FIGURE 56)

SECTION V - CARE

MAINTENANCE (CONTINUED)

Service

Runtimes

Sensors

Motors

Alerts

High Pressure Mode

Maintenance Mode

07:33:14 PM

Maintenance Mode

LTE

Settings

Technical

Info

Home

Network

FIGURE 55. PRESS SERVICE >

(Continued on the next page.)

FIGURE 54. REMOVE INTAKE FILTER CAP

INTAKE

FILTER

CAP

SCREWS

(2)

INTAKE

FILTER

FIGURE 53. ENABLE MAINTENANCE MODE

Service

Runtimes

Sensors

Motors

Alerts

High Pressure Mode

Maintenance Mode

07:33:14 PM

Maintenance Mode

LTE

Settings

Technical

Info

Home

Network

Technical

Select item for service

Motor 1

Motor 2

Filter
Pack

Desiccant

Tower

Pressure

Sensor

Ambient

Sensor

Dew Point

Sensor

Service

Desiccant

Cartridge

FIGURE 56. PRESS FILTER PACK

Summary of Contents for Aeras Ramvac C11














































































Search results

Summary of Contents for Aeras Ramvac C11

Reviews:

Related manuals for Aeras Ramvac C11

Brands by name

Popular brands

DentalEZ Aeras Ramvac C11, User Manual

Search results

Summary of Contents for Aeras Ramvac C11

Reviews:

Related manuals for Aeras Ramvac C11

Brands by name

Popular brands