Delta Regis DRFF-300R User Manual Download

Page: 3 / 27

Table of Contents

Check before Use ................................................................................................................................ 1

Equipped Accessories .................................................................................................................. 1

Check Screw Dimension .............................................................................................................. 1

Description of Machine & PCB Function and Panel Hole Locations ........................................... 2

Adjustment ......................................................................................................................................... 3

Track Adjustment ......................................................................................................................... 3

Track Removal ..................................................................................................................... 3

Adjust Track Width .............................................................................................................. 5

Track Installation ................................................................................................................. 7

Adjustment of Keep Board .......................................................................................................... 8

Adjustment of Infrared Device .................................................................................................... 9

Adjustment of Dispensing Mechanism ...................................................................................... 10

Adjustment of Container Funnel Inside Cylinder ...................................................................... 13

Adjustment of Brush .................................................................................................................. 14

Method of Use ................................................................................................................................... 16

Quantity of Screws Placed In ..................................................................................................... 16

Signal Board Connection ........................................................................................................... 17

Counter Interface Operation ....................................................................................................... 18

Common Malfunction and Simple Resolution .............................................................................. 21

Maintenance and Cleaning .............................................................................................................. 22

Warranty Clause .............................................................................................................................. 23

Summary of Contents for DRFF-300R




























Search results

Summary of Contents for DRFF-300R

Reviews:

Related manuals for DRFF-300R

Brands by name

Popular brands

Delta Regis DRFF-300R, User Manual

Search results

Summary of Contents for DRFF-300R

Reviews:

Related manuals for DRFF-300R

Brands by name

Popular brands