manualshive.com logo in svg

Dell Precision Workstation 490, User Manual

Share
Download
Dell Precision Workstation 490 User Manual Download Page 93

Expansion Bus 

Bus type 

PCI 2.3 
PCI Express 1.0A 
PCI-X 2.0A 
USB 2.0 

Bus speed 

PCI:

 133 MB/s 

PCI-X:

 800 MB/s 

PCI Express: 

x4/ x8 slot bidirectional speed - 2 GB/s 
x16 slot bidirectional speed - 8 GB/s 

Card Slots 

Desktop Mode:

 Slots 2-4 support full-length cards (1 

PCI Express x16 slot, one PCI Express x8 slot, and 
one PCI slot), and slots 1, 5, and 6 support half-
length cards (2 PCI-X slots and 1 PCI Express x8 
slot). 

Tower Mode:

 Slots 2-5 support full-length cards (1 

PCI-X slot, one PCI Express x8 slot, 1 PCI Express 
x16 slot, and one PCI slot), and slots 1 and 6 support 
half-length cards (1 PCI-X slot and 1 PCI Express x8 
slot). 

PCI 

 

 

connector 

one 

connector size 

120 pins

 

connector data width (maximum) 

32 bits

 

PCI-X 

 

 

connectors 

two 

connector size 

188 pins

 

connector data width (maximum) 

64 bits

 

PCI Express x8 (wired as x4) 

 

 

connectors 

two x8 (support x8, x4, and x1 modes/cards; 
maximum x4 link width) 

connector size 

98 pins 

connector data width (maximum) 

4 PCI Express lanes 

PCI Express x16 

 

 

connector 

one x16 slot (supports x16, x8, x4 and x1 
modes/cards) 

connector size 

164 pins 

connector data width (maximum) 

16 PCI Express lanes 

 

 

Drives 

Externally accessible: 

one 3.5-inch drive bay (FlexBay) 

two 5.25-inch drive bays 

Internally accessible: 

two 3.5-inch hard-drive bays 

 

 

Connectors 

External connectors: 

Serial 

two 9-pin connectors; 16550C-compatible 

Parallel 

25-hole connector (bidirectional) 

IEEE 1394 (optional) 

one front-panel 6-pin connector (with optional card) 

Network adapter 

RJ45 connector 

PS/2 (keyboard and mouse) 

two 6-pin mini-DIN 

USB 

two front-panel and five back-panel USB 2.0

–

compliant connectors 

Audio 

two front-panel connectors for microphone and 
headphones; 
two back-panel connectors for line-in and line-out/ 
headphones 

System board connectors: 

IDE drive 

40-pin connector 

Floppy drive 

34-pin connector 

Serial ATA 

five 7-pin connectors 

Internal USB 

10-pin connector for optional Media Card Reader (3.5-
inch bay device) 

Summary of Contents for Precision Workstation 490











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands