manualshive.com logo in svg

Dell Precision Workstation 490, User Manual

Share
Download
Dell Precision Workstation 490 User Manual Download Page 88

  

 

 

13.

Replace the desktop drive retention insert and fold down its handle.  
 

 

  

14.

Check all cable connections, and fold cables out of the way to allow for airflow between the fan and cooling vents.  
 

 

  

15.

Reinstall the drive panel (see 

Replacing the Drive Panel

).  

 

 

  

16.

Ensure that all connectors are properly cabled and firmly seated.  
 

 

  

17.

Replace the computer cover (see 

Replacing the Computer Cover

).  

 

 

 

18.

Connect your computer and devices to their electrical outlets, and turn them on.  
 

See the documentation that came with the drive for instructions on installing any software required for drive operation. 

 

 

19.

Enter the system setup program (see 

System Setup

) and select the appropriate 

Drive

 option.  

 

 

  

20.

Verify that your computer works correctly by running the Dell Diagnostics. See 

Dell Diagnostics

 for instructions.  

 

Back to Contents Page

 

 

 

1  power cable 

2  IDE data cable 

3  SATA data cable 

4  system-board SATA optical connector 

5  system-board IDE connector 

 

NOTICE: 

To connect a network cable, first plug the cable in to the network port or device and then plug it in to the computer.

Summary of Contents for Precision Workstation 490











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands