manualshive.com logo in svg

Dell Precision Workstation 490, User Manual

Share
Download
Dell Precision Workstation 490 User Manual Download Page 116

  

 

 

6.

If the system is in tower mode, pull to remove the full-length card retainer piece beside the card fan.  
 

 

  

7.

Press the tab between the card fan and the front fan towards the card fan as you lift it up and out of the computer.  
 

 

 

8.

Note the routing of each cable as you disconnect all cables attached to the I/O panel.  
 

  

 

 

9.

Remove the mounting screw from the I/O panel.  
 

 

  

10.

Remove the I/O panel from the computer.  
 

 

Replacing the I/O Panel  

Follow 

Removing the I/O Panel

 in reverse order. 

1  card fan 

2  card fan cable 

3  card fan system-board connector (FAN_CCAG) 

4  front fan 

5  full-length card retainer piece 

 

NOTICE: 

Carefully note the routing of each cable before you disconnect it, so that you are sure to re-route cables correctly. An incorrectly routed or a 

disconnected cable could lead to computer problems.

1  I/O panel 

2  mounting screw 

 

NOTICE: 

Ensure that you replace all cables originally attached to the I/O panel or you may experience computer problems.

Summary of Contents for Precision Workstation 490











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands