manualshive.com logo in svg

Dell Precision Workstation 490, User Manual

Share
Download
Dell Precision Workstation 490 User Manual Download Page 130

Back to Contents Page

  

 

 Replacing the Front Panel and Computer Cover  

Dell Precision™ Workstation 490 User's Guide

 

  

Rotating the Hard-Drive Carrier Back into the Computer 

 

  

Replacing the Front Panel 

 

  

Replacing the Computer Cover 

 

 

 

 

 

 

 

Rotating the Hard-Drive Carrier Back into the Computer  

 

 

1.

Grasp the handle on the hard-drive carrier and rotate the carrier back into the chassis until the metal tabs on each side of the carrier are seated, 
securing the carrier.  
 

  

 

 

2.

Pull up on the card retention mechanism to release it from the hard-drive carrier.  
 

  

 

CAUTION: 

Before you begin any of the procedures in this section, follow the safety instructions in the 

Product Information Guide

.

 

CAUTION: 

To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover.

 

NOTICE: 

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your 

computer's electronic components. You can do so by touching an unpainted metal surface on the computer.

1  rotatable hard-drive carrier 

2  handle 

3  card-retention mechanism 

1  card-retention mechanism tab 

Summary of Contents for Precision Workstation 490











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands