manualshive.com logo in svg

Dell Precision Workstation 490, User Manual

Share
Download
Dell Precision Workstation 490 User Manual Download Page 55

  

 

 

9.

Slide the hard drive into the hard-drive bay until it clicks securely into place.  
 

 

  

10.

Connect a power cable to the hard drive.  
 

 

 

11.

If you are installing a SATA hard drive

, connect the data cable to the hard drive.  

 

  

If you are installing a SAS hard drive, 

connect the data cable on the SAS controller card to the hard drive. 

  

1  drive 

2  hard-drive bracket 

 

NOTICE: 

SAS drives and SATA drives cannot be mixed in the rotatable hard-drive carrier. The drives in the hard-drive carrier must both be either SATA or 

SAS hard drives.

 

NOTICE: 

The only SATA connectors on the board that support hard drives are those labeled SATA0, SATA1, and SATA2.

1  P3 power connector  3  hard-drive power cable 

2  SATA data cable 

4  hard-drive 

Summary of Contents for Precision Workstation 490











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands