manualshive.com logo in svg

Dell Precision Workstation 490, User Manual

Share
Download
Dell Precision Workstation 490 User Manual Download Page 132

  

 

 

4.

Connect your computer and devices to electrical outlets, and turn them on.  
 

 

  

5.

After you open and close the cover, the chassis intrusion detector, if enabled, causes the following message to appear on the screen at the next 
computer start-up:  
 

ALERT! Cover was previously removed. 

 

 

6.

Reset the chassis intrusion detector by changing Intrusion Alert to Enabled or Enabled-Silent. See 

Resetting the Chassis Intrusion Detector

.  

 

 

  

7.

If a setup password has been assigned by someone else, contact your network administrator for information on resetting the chassis intrusion detector. 
 
 

Back to Contents Page

 

 

 

1  computer cover 

2  computer base 

 

NOTICE: 

To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.

Summary of Contents for Precision Workstation 490











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands