manualshive.com logo in svg

Dell Precision Workstation 490, User Manual

Share
Download
Dell Precision Workstation 490 User Manual Download Page 115

Back to Contents Page

  

 

 I/O Panel  

Dell Precision™ Workstation 490 User's Guide

 

  

I/O-Panel Components 

 

  

Removing the I/O Panel 

 

  

Replacing the I/O Panel 

 

 

 

 

 

 

 

I/O-Panel Components  

  

 

Removing the I/O Panel  

 

 

1.

Follow the procedures in 

Before You Begin

.  

 

 

  

2.

Remove the computer cover (see 

Removing the Computer Cover

).  

 

 

  

3.

Rotate the hard-drive carrier out of the computer (see 

Rotating the Hard-Drive Carrier Out of the Computer

).  

 

 

  

4.

Disconnect the optional speaker connector (if installed) from the system board.  
 

 

  

5.

Disconnect the card fan connector from the system board.  
 

 

CAUTION: 

Before you begin any of the procedures in this section, follow the safety instructions in the 

Product Information Guide

.

 

CAUTION: 

To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover.

 

NOTICE: 

To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your 

computer's electronic components. You can do so by touching an unpainted metal surface on the computer.

1  USB ports 

2  diagnostic, hard-drive access, and network integrity lights 

3  headphone connector 

4  microphone connector 

5 

front-panel thermal diode connector 

 

 

NOTICE: 

The front-panel thermal diode cable must be installed in this connector at all times while your computer is running or thermal problems may 

result. 

Summary of Contents for Precision Workstation 490











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands