Dell PowerEdge 860 Hardware Owner'S Manual Download Page 99

Page: 99 / 140

Jumpers and Connectors

Riser Card Connectors

The system is available with either a PCIe riser card or a PCI-X/PCIe riser card. See Figure 6-3 and
Figure 6-4 for the location and description of the expansion-card slots on the two riser cards.

Table 6-2.

System Board Connectors

Item

Connector

Description

PROC

Processor socket

12V

power supply connector

PWR_CONN

power supply connector

DIMM 1

Memory module

DIMM 3

Memory module

DIMM 2

Memory module

DIMM 4

Memory module

FAN

Power connector for the fans

BATTERY

Connector for the 3.0 V coin battery

SATA_0

Connector for the SATA 0 hard drive

SATA_1

Connector for the SATA 1 hard drive

PCI FAN

Connector for the PCI fan

FP_CONN1

Control panel interface connector

IDE

Optical drive interface connector

HD_ACT

Hard drive activity connector (expansion controller)

INTRUSION_SWITCH

Connector for the chassis intrusion switch

I2C HEADER

Remote access controller connector

BMC PROG

Remote access controller connector

RISER_CONN1

Riser card interface connector

Summary of Contents for PowerEdge 860













































































































































Search results

Summary of Contents for PowerEdge 860

Reviews:

Related manuals for PowerEdge 860

Brands by name

Popular brands

Dell PowerEdge 860, Hardware Owner'S Manual

Search results

Summary of Contents for PowerEdge 860

Reviews:

Related manuals for PowerEdge 860

Brands by name

Popular brands