Dell PowerEdge 860 Hardware Owner'S Manual Download Page 41

Page: 41 / 140

Using the System Setup Program

•

Control of system functions including power on and off

•

Support is independent of the system’s power or operating state

•

Provides text console redirection for system setup, text-based utilities, and operating system consoles

NOTE:

To remotely access the BMC through the integrated NIC, you must connect the network connection to

integrated NIC1.

For additional information on using BMC, see the documentation for the BMC and systems management
applications.

Entering the BMC Setup Module

Turn on or restart your system.

Press <

Ctrl-E

> when prompted after POST.

If your operating system begins to load before you press <

Crtl-E

>, allow the system to finish

booting, and then restart your system and try again.

BMC Setup Module Options

For information about the BMC Setup Module options and how to configure the emergency management
port (EMP), see the

BMC User’s Guide

Summary of Contents for PowerEdge 860













































































































































Search results

Summary of Contents for PowerEdge 860

Reviews:

Related manuals for PowerEdge 860

Brands by name

Popular brands

Dell PowerEdge 860, Hardware Owner'S Manual

Search results

Summary of Contents for PowerEdge 860

Reviews:

Related manuals for PowerEdge 860

Brands by name

Popular brands