Dell PowerEdge 860 Hardware Owner'S Manual Download Page 76

Page: 76 / 140

Installing System Components

Figure 3-21.

Installing and Removing the System Board

Installing the System Board Assembly

CAUTION:

Only trained service technicians are authorized to remove the system cover and access any of the

components inside the system. Before performing any procedure, see your

Product Information Guide

for

complete information about safety precautions, working inside the computer and protecting against electrostatic
discharge.

Unpack the new system board assembly.

Align the system board tray so that the tabs on the chassis floor slide into the notches in the system
board tray.

Slide the system board tray backward until it stops.

Press down on the plunger that secures the system board tray to the chassis. See Figure 3-21.

plunger

system board 3

system

board

tray

Summary of Contents for PowerEdge 860













































































































































Search results

Summary of Contents for PowerEdge 860

Reviews:

Related manuals for PowerEdge 860

Brands by name

Popular brands

Dell PowerEdge 860, Hardware Owner'S Manual

Search results

Summary of Contents for PowerEdge 860

Reviews:

Related manuals for PowerEdge 860

Brands by name

Popular brands