Dell PowerEdge 860 Hardware Owner'S Manual Download Page 58

Page: 58 / 140

Installing System Components

Figure 3-11.

Installing and Removing the Fan Assembly

Installing the Fan Assembly

Align the holes in the fan assembly with the two fan assembly securing posts. See Figure 3-11.

Lower the fan assembly until the release levers snap onto the securing posts.

Route the cables in the fan assembly cable tray. See Figure 3-11.

Reconnect the hard drive 1 data cable to the hard drive. See Figure 3-11.

Reconnect the fan assembly power cable to the system board.

Install the cooling shroud. See "Installing the Cooling Shroud" on page 48.

Close the system. See "Closing the System" on page 47.

release levers (2)

power cable

securing posts (2)

hard drive 1 data cable

cable tray

Summary of Contents for PowerEdge 860













































































































































Search results

Summary of Contents for PowerEdge 860

Reviews:

Related manuals for PowerEdge 860

Brands by name

Popular brands

Dell PowerEdge 860, Hardware Owner'S Manual

Search results

Summary of Contents for PowerEdge 860

Reviews:

Related manuals for PowerEdge 860

Brands by name

Popular brands