Dell PowerEdge 7250 User Manual Download Page 77

Page: 77 / 102

Terminal Mode Commands

SYS SET TCFG

Returns the Terminal Mode Configuration bytes where XX and YY

represent hex-ASCII encoding for the volatile version of data bytes

1 and 2 as specified in Table C-6, and AA BB represent hex-ASCII

encoding of the non-volatile version.
V:XX Output termination sequence>
N:AA BB <output termination sequence>

-V XX YY

This command sets the volatile Terminal Mode Configuration. XX

and YY represent hex-ASCII encoding for data bytes 1 and 2 as

specified in Table C-6. The BMC returns the same output as for

SYS SET TCFG, above.

-N XX YY

This command sets the non-volatile Terminal Mode

Configuration. XX and YY represent hex-ASCII encoding for data

bytes 1 and 2 as specified in Table C-6. The BMC returns the same

output as for SYS SET TCFG, above.

SYS RESET

Directs the BMC to perform an immediate system hard reset.

SYS POWER

OFF

Directs the BMC to perform an immediate system power off.

SYS POWER ON

Causes the BMC to initiate an immediate system power on.

Table C-4. Terminal Mode Text Commands

(continued)

Command

Switches

Description

Summary of Contents for PowerEdge 7250







































































































Search results

Summary of Contents for PowerEdge 7250

Reviews:

Related manuals for PowerEdge 7250

Brands by name

Popular brands

Dell PowerEdge 7250, User Manual

Search results

Summary of Contents for PowerEdge 7250

Reviews:

Related manuals for PowerEdge 7250

Brands by name

Popular brands