Dell PowerEdge 7250 User Manual Download Page 35

Page: 35 / 102

BMC Management Utility

IPMI Shell Global Options

IPMI Shell has the following global options:

IPMI Session Option

-ip

Synopsis

ipmish

bmc_ip_address

bmc_hostname

username

password

Description

This option is used to establish a connection to a remote managed system using the LAN channel.

The IP port specified in installation (default value is 623) is used unless another port has been

configured.

Options

NOTE:

The following options cannot be used independently. One or more IPMISH command must follow

the option.

-ip

bmc_ip_address

bmc_hostname

Specifies the IP address or hostname of the remote managed system.

-u

username

Specifies the BMC username used to connect to the system.

-p

password

Specifies the BMC user password used to connect to the system.

IPMI Session Option

-com

Synopsis

ipmish

com

serial_port

-baud

baud_rate

flow

flow_control

username

password

Description

This option is used to establish a connection to a remote managed system using the serial channel.

Summary of Contents for PowerEdge 7250







































































































Search results

Summary of Contents for PowerEdge 7250

Reviews:

Related manuals for PowerEdge 7250

Brands by name

Popular brands

Dell PowerEdge 7250, User Manual

Search results

Summary of Contents for PowerEdge 7250

Reviews:

Related manuals for PowerEdge 7250

Brands by name

Popular brands