Dell PowerEdge 7250 User Manual Download Page 39

Page: 39 / 102

BMC Management Utility

Subcommands

off

Turns the managed system’s front panel LED on or off. If the BMC supports the IPMI extension

Chassis Identify On

command, then the

identify on

command turns the LED on indefinitely until

the

identify off

command is used to turn the LED off. Otherwise, the LED will be turned on for

the maximum allowed time of 255 seconds.

Options

-t

seconds

Specifies how long the LED is on. It should be no longer than 255 seconds.

Default Subcommand

If a subcommand is not specified, this command acts the same as the

identify on

command.

Figure 3-5. identify Option Example

sysinfo

Synopsis

sysinfo

[

fru

]

Description

This command retrieves and displays the system information, including field replaceable unit

(FRU) and BMC information for the managed system. See Figure 3-6.

Summary of Contents for PowerEdge 7250







































































































Search results

Summary of Contents for PowerEdge 7250

Reviews:

Related manuals for PowerEdge 7250

Brands by name

Popular brands

Dell PowerEdge 7250, User Manual

Search results

Summary of Contents for PowerEdge 7250

Reviews:

Related manuals for PowerEdge 7250

Brands by name

Popular brands