Dell PowerEdge 7250 User Manual Download Page 41

Page: 41 / 102

BMC Management Utility

Subcommands

status

— Displays the current power status of the system, the returned value is “on” or “off”.

— Turns on the managed system.

off

— Issues a “graceful shutdown” IPMI command.

NOTE:

The off subcommand is not supported on the PowerEdge 7250. You must use the force option to

turn off the system.

cycle

— Turns off the system, pauses, then turns the system back on.

reset

— Pulses the system reset signal, regardless of the power state.

Options

-force

This option simulates pressing the power button, forcing the system to turn off without shutting

down the operating system.

Default Subcommand

If a subcommand is not specified, this command acts the same as

power status

Figure 3-7. power Option Example

Summary of Contents for PowerEdge 7250







































































































Search results

Summary of Contents for PowerEdge 7250

Reviews:

Related manuals for PowerEdge 7250

Brands by name

Popular brands

Dell PowerEdge 7250, User Manual

Search results

Summary of Contents for PowerEdge 7250

Reviews:

Related manuals for PowerEdge 7250

Brands by name

Popular brands