manualshive.com logo in svg

Dell Inspiron 5521, Service Manual

Share
Download
Dell Inspiron 5521 Service Manual Download Page 83

Camera/microphone module

Removing the camera

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

2. Enter 

Service Mode

.

3. Remove the 

SIM card

.

4. Remove the 

microSD card

.

5. Remove the 

base cover

.

6. Remove the 

display assembly

.

7. Remove the 

display bezel

.

8. Remove the 

display panel

.

9. Remove the 

display hinges

.

About this task

The following images indicate the location of the camera module and provide a visual representation of the removal procedure.

Steps

1. Peel the tape that secures the camera cable.

NOTE:

 An abrupt peeling may also remove the camera shutter from the display bezel and damage the camera shutter.

2. Lift the latch and disconnect the camera cable from the connector on the camera module.
3. Carefully pry up the camera module starting from the prying point at the bottom edge of the camera module.
4. Carefully lift the camera module from the display back cover.

Installing the camera

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Removing and installing components

83

Summary of Contents for Inspiron 5521























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands