manualshive.com logo in svg

Dell Inspiron 5521, Service Manual

Share
Download
Dell Inspiron 5521 Service Manual Download Page 82

Steps

1. Connect the display cable to the connector on the display panel and close the latch.
2. Adhere the clear tape to cover the display cable connector.
3. Adhere the conductive tape to secure the display cable to the display panel.
4. Close the display panel and the display back cover to assemble.

NOTE:

 Ensure that the display panel tabs are inserted into the slots on the display cover.

5. Replace the four (M2.5x3.5) screws to secure the display panel to the display back cover.

Next steps

1. Install the 

display bezel

.

2. Install the 

display assembly

.

3. Install the 

WWAN card

.

4. Install the 

WLAN card

.

5. Install the 

base cover

.

6. Install the 

microSD card

.

7. Install the 

SIM card

.

8. Exit 

Service Mode

.

9. Follow the procedure in 

After working inside your computer

.

82

Removing and installing components

Summary of Contents for Inspiron 5521























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands