Dell Inspiron 5521 Service Manual Download Page 4

Page: 4 / 118

Removing the 4-cell battery..................................................................................................................................... 39
Installing the 4-cell battery....................................................................................................................................... 40

Assembly inner frame........................................................................................................................................................41

Removing the assembly inner frame........................................................................................................................41
Installing the assembly inner frame.........................................................................................................................43

LED board............................................................................................................................................................................44

Removing the LED board...........................................................................................................................................44
Installing the LED board.............................................................................................................................................45

Heat sink..............................................................................................................................................................................46

Speakers.............................................................................................................................................................................. 52

Removing the speakers..............................................................................................................................................52
Installing the speakers................................................................................................................................................52

USB type-C bracket......................................................................................................................................................... 53

Removing the USB type-C bracket........................................................................................................................ 53
Installing the USB type-C bracket...........................................................................................................................54

System board..................................................................................................................................................................... 55

Removing the system board.....................................................................................................................................55
Installing the system board....................................................................................................................................... 57

Power-button board.........................................................................................................................................................59

Removing the power-button board........................................................................................................................ 59
Installing the power-button board...........................................................................................................................60

Smart card reader..............................................................................................................................................................61

Removing the smart card reader..............................................................................................................................61
Installing the smart card reader............................................................................................................................... 62

Coin-cell battery................................................................................................................................................................64

Removing the coin-cell battery................................................................................................................................64
Installing the coin-cell battery..................................................................................................................................65

Keyboard assembly........................................................................................................................................................... 66

Removing the keyboard assembly...........................................................................................................................66
Installing the keyboard assembly............................................................................................................................. 67

Keyboard bracket.............................................................................................................................................................. 69

Removing the keyboard bracket..............................................................................................................................69
Installing the keyboard bracket................................................................................................................................ 70

Display assembly.................................................................................................................................................................71

Removing the display assembly................................................................................................................................ 71
Installing the display assembly..................................................................................................................................73

Display bezel....................................................................................................................................................................... 75

Removing the display bezel.......................................................................................................................................75
Installing the display bezel.........................................................................................................................................76

Display panel....................................................................................................................................................................... 77

Removing the display panel....................................................................................................................................... 77
Installing the display panel.........................................................................................................................................80

Camera/microphone module.......................................................................................................................................... 83

Removing the camera.................................................................................................................................................83
Installing the camera...................................................................................................................................................83

eDP/display cable..............................................................................................................................................................84

Contents

Summary of Contents for Inspiron 5521























































































































Search results

Summary of Contents for Inspiron 5521

Reviews:

Brands by name

Popular brands

Dell Inspiron 5521, Service Manual

Search results

Summary of Contents for Inspiron 5521

Reviews:

Brands by name

Popular brands