manualshive.com logo in svg

Dell Inspiron 5521, Service Manual

Share
Download
Dell Inspiron 5521 Service Manual Download Page 70

Installing the keyboard bracket

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE:

 The system board can be installed with the heat sink attached in order to simplify the procedure and preserve the

thermal bond between the system board and heat sink.

The following image indicates the location of the keyboard bracket and provides a visual representation of the installation
procedure.

Steps

1. Align and place the keyboard on the keyboard bracket.
2. Replace the fourteen (M2x2) screws to secure the keyboard to the keyboard bracket.

Next steps

1. Install the 

keyboard assembly

.

2. Install the 

system board

.

3. Install the 

assembly inner frame

.

4. Install the 

speakers

.

5. Install the heat sink - 

UMA

 or 

discrete

 based on the system configuration.

6. Install the 

battery

.

7. Install the 

WWAN card

.

8. Install the 

WLAN card

.

9. Install the 

2280 solid-state drive

 or 

2230 solid-state drive

.

10. Install the 

memory module

.

11. Install the 

base cover

.

12. Install the 

microSD card

.

13. Install the 

SIM card

.

14. Exit 

Service Mode

.

15. Follow the procedure in 

After working inside your computer

.

70

Removing and installing components

Summary of Contents for Inspiron 5521























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands