manualshive.com logo in svg

Dell Inspiron 5521, Service Manual

Share
Download
Dell Inspiron 5521 Service Manual Download Page 31

5. Remove the 

base cover

.

About this task

NOTE:

 Depending on the configuration ordered, your computer may support a 2280 solid-state drive, or a 2230 solid-state

drive in M.2 slot.

NOTE:

 This procedure applies only to computers shipped with a 2280 solid-state drive installed in M.2 slot.

The following image indicates the location of the 2280 solid-state drive that is installed in M.2 slot and provides a visual
representation of the removal procedure.

Steps

1. Remove the two (M2x2) screws that secures the solid-state drive thermal plate to the palm-rest and keyboard assembly.
2. Remove the solid-state drive thermal plate out of the system.
3. Slide and lift the 2280 solid-state drive off the M.2 solid-state drive slot on the system.

Installing the 2280 solid-state drive

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE:

 Solid-state drives are fragile. Exercise care when handling the solid-state drive.

NOTE:

 Depending on the configuration ordered, the computer one may support a 2280 solid-state drive, or a 2230

solid-state drive in M.2 slot.

NOTE:

 This procedure is applicable if you are installing a 2280 solid-state drive in M.2 slot.

The following image indicates the location of the 2280 solid-state drive that is installed in M.2 slot and provides a visual
representation of the installation procedure.

Removing and installing components

31

Summary of Contents for Inspiron 5521























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands