Dell Alienware m17 Service Manual Download

Page: 113 / 119

Table 5. System setup options—Security menu (continued)

Security

BIOS PPI user prompts when issuing the Clear command.
Changes to this setting take effect immediately.

Default: Enabled

UEFI Capsule Firmware Updates

Enable or disable BIOS updates through UEFI capsule
update packages.

Default: Enabled

Table 6. System setup options—Boot menu

Boot

Boot List Option

Displays the available boot options.

Default: UEFI

File Browser Add Boot Option

Enables you to add the boot options.

File Browser Del Boot Option

Enables you to delete the boot options

Secure Boot

Enable or disable the secure boot feature.

Default: Disabled

Legacy Option ROMs

Enable or disable the Legacy Option ROMs.

Default: Disabled

Attempt Legacy Boot

Enable or disable Attempt Legacy Boot.

Default: Disabled

Boot Option Priorities

Displays the boot sequence.

Boot Option #1

Displays the available first boot option.

Boot Option #2

Displays the available second boot option.

Boot Option #3

Displays the available third boot option.

Table 7. System setup options—Exit menu

Exit

Save Changes and Reset

Allows you to exit system setup and save your changes.

Discard Changes and Reset

Allows you to exit system setup and load previous values for
all system setup options.

Restore Defaults

Allows you to restore default values for all system setup
options.

Discard Changes

Allows you to load previous values for all system setup
options.

Save Changes

Allows you to save the changes for all system setup
options.

Clearing CMOS settings

CAUTION:

Clearing CMOS settings will reset the BIOS settings on your computer.

1. Remove the

base cover

2. Disconnect the battery cable from the system board.
3. Remove the

coin-cell battery

System setup

113

Summary of Contents for Alienware m17
























































































































Search results

Summary of Contents for Alienware m17

Reviews:

Related manuals for Alienware m17

Brands by name

Popular brands

Dell Alienware m17, Service Manual

Search results

Summary of Contents for Alienware m17

Reviews:

Related manuals for Alienware m17

Brands by name

Popular brands