Dell Alienware m17 Service Manual Download

Page: 84 / 119

Removing the display back-cover and

antenna assembly

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Prerequisites

1. Remove the

2. Remove the

3. Remove the

4. Remove the

5. Remove the

Procedure

NOTE:

Ensure that the display assembly is placed on a clean and flat surface.

After performing all the pre-requisites you are left with the display back-cover and antenna assembly.

Removing the display back-cover and antenna assembly

Summary of Contents for Alienware m17
























































































































Search results

Summary of Contents for Alienware m17

Reviews:

Related manuals for Alienware m17

Brands by name

Popular brands

Dell Alienware m17, Service Manual

Search results

Summary of Contents for Alienware m17

Reviews:

Related manuals for Alienware m17

Brands by name

Popular brands