Dell Alienware m17 Service Manual Download Page 108

Page: 108 / 119

Device drivers

Intel Chipset Software Installation Utility

In the Device Manager, check if the chipset driver is installed.

Install the Intel chipset updates from

www.dell.com/support

Video drivers

In the Device Manager, check if the video driver is installed.

Install the video driver update from

www.dell.com/support

Intel Serial IO driver

In the Device Manager, check if the Intel Serial IO driver is installed.

Install the driver updates from

www.dell.com/support

Intel Trusted Execution Engine Interface

In the Device Manager, check if the Intel Trusted Execution Engine Interface driver is installed.

Install the driver update from

www.dell.com/support

Intel Virtual Button driver

In the Device Manager, check if the Intel Virtual Button driver is installed.

Install the driver updates from

www.dell.com/support

Wireless and Bluetooth drivers

In the Device Manager, check if the network card driver is installed.

Install the driver updates from

www.dell.com/support

In the Device Manager, check if the Bluetooth driver is installed.

Install the driver updates from

www.dell.com/support

108

Device drivers

Summary of Contents for Alienware m17
























































































































Search results

Summary of Contents for Alienware m17

Reviews:

Related manuals for Alienware m17

Brands by name

Popular brands

Dell Alienware m17, Service Manual

Search results

Summary of Contents for Alienware m17

Reviews:

Related manuals for Alienware m17

Brands by name

Popular brands