Dell Alienware m17 Service Manual Download Page 90 | Manualshive

Page: 90 / 119

background image

7. Connect the power-adapter port cable to the system board.
8. Connect the display cable and close the latch to secure the cable.
9. Adhere the tape that secures the display cable to the system board.
10. Connect the power-button board cable to the system board.
11. Place and align the USB Type-C port bracket on the palm-rest assembly.
12. Replace the two screws (M2x3) that secure the USB Type-C port bracket to the palm-rest assembly.
13. Connect the camera cable to the system board and adhere the tape that secures the camera cable to the system board.
14. Connect the coin-cell battery to the system board.
15. Connect the I/O-board cable to the system board and close the latch to secure the cable.
16. Adhere the tape that secures the I/O-board cable connector latch to the system board.

Post-requisites

1. Follow the procedure from step 2 to step 6 in

Replacing the heat sink

2. Replace the

solid-state drive/Intel Optane

.

3. Replace the

4. Replace the

.

5. Follow the procedure from step 4 to step 6 in

Replacing the hard drive

.

6. Replace the

battery (half-length)

or the

battery (full-length)

, whichever applicable.

7. Replace the

.

90

Replacing the system board

«
...
88
89
90
91
92
...
»

Summary of Contents for Alienware m17
























































































































Reviews:

No comments

Related manuals for Alienware m17

Toughbook CF-T7BWATAAM

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 40

600E - ThinkPad 2645 - PII 400 MHz

Brand: IBM Pages: 4

600E - ThinkPad 2645 - PII 400 MHz

Brand: IBM Pages: 4

2621483 - ThinkPad i Series 1400 2621

Brand: IBM Pages: 6

Brand: IBM Pages: 22

Brand: IBM Pages: 148

Brand: IBM Pages: 3

Toughbook CF-74JCL02AM

Brand: Panasonic Pages: 36

Fairies Magic JC262i1

Brand: LEXIBOOK Pages: 32

Brand: Huawei Pages: 120

Brand: HP Pages: 43

4320t - Mobile Thin Client

Brand: HP Pages: 92

2710p - Compaq Business Notebook

Brand: HP Pages: 58

Brand: HP Pages: 117

2730p - EliteBook - Core 2 Duo 1.86 GHz

Brand: HP Pages: 126

6530b - Compaq Business Notebook

Brand: HP Pages: 40

2730p - EliteBook - Core 2 Duo 1.86 GHz

Brand: HP Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands