Datex-Ohmeda S/5 B-GAS Technical Reference Manual Download Page 60

Page: 60 / 83

Datex-Ohmeda S/5 Anesthesia Monitor

Document No. 800 1005-1

4.8

Error messages

Message

Explanation

Occlusion

The sample tube inside or outside the monitor is blocked or water trap is
occluded. If occlusion persists, measured gas values disappear.

Air leak

- the water trap is not connected
- the gas outlet is blocked
- there is a leak in the sampling line inside the module. If air leak persists
measured gas values disappear.

Replace trap

Indicates residue build-up on the water trap membrane. This decreases air
flow.

Zero valve error

Opening the valve does not change working pressure enough.

Gas calibration is not available during the first 5
minutes/during occlusion/during air leak

Calibration not allowed during the first 5 minutes after power up and in
mentioned situations.

Select agent

No agent selected.

Continuous occlusion. Check sampling line and water trap.

Occlusion over 40 seconds.

Air leak detected. Check water trap and sample gas out-flow.
Press normal screen to continue.

Air leak over 40 seconds.

CO2

Zero error

Unsuccessful zeroing

Unstable

Unsuccessful calibration

CO2 over scale

CO2 signal exceeds the maximum waveform area

O2 zero error

Unsuccessful zeroing

O2 over scale

O2 signal exceeds the maximum waveform area

O2 Unstable

Unsuccessful calibration

N2O

N2O zero error

Unsuccessful zeroing

N2O Unstable

Unsuccessful calibration

Ane agents
AA zero error
Zero error

Unsuccessful zeroing

AA unstable
Unstable

Unsuccessful calibration

AA over scale

AA signal exceeds the maximum waveform area

Menu messages during calibration
Zero error

Unsuccessful zeroing

Adjust

Calibration gas accepted and monitor is ready for adjusting the gas values
to match the calibration gas concentration

Unstable

Unsuccessful calibration

Summary of Contents for S/5 B-GAS




















































































Search results

Summary of Contents for S/5 B-GAS

Reviews:

Related manuals for S/5 B-GAS

Brands by name

Popular brands

Datex-Ohmeda S/5 B-GAS, Technical Reference Manual

Search results

Summary of Contents for S/5 B-GAS

Reviews:

Related manuals for S/5 B-GAS

Brands by name

Popular brands