manualshive.com logo in svg

Datex-Ohmeda S/5 B-GAS, Technical Reference Manual

Share
Download
Datex-Ohmeda S/5 B-GAS Technical Reference Manual Download Page 55

S/5 Airway modules

Document No. 800 1005-1

49

4.2

 

Gas sampling system troubleshooting

The faults which can occur in the sampling system are: leaks or blockages in the tubing, failure of

the sampling pump or the magnetic valves, or diminishing of the flow rates because of pump aging

or dirt accumulating in the internal tubing.
The following checks should help in localizing the fault. Whenever suspecting the sampling system

and always after working on the sampling system check and if necessary adjust the flow rates.
The sampling system details are illustrated in figures 5, 6, 7 and 8.

CAUTION

 

The special internal sample tube is mechanically fragile. Sharp bends will cause

leaks.

NOTE: D-fend water trap should be replaced when the OCCLUSION message appears during the

monitor startup.
NOTE: If any liquid has entered the ACX-200 measuring unit due to water trap filter failure, contact

Datex-Ohmeda technical services.

4.2.1

 

Sampling system leak test

Connect power cord and sampling line. Turn the power on and wait until the initialization is over.
1.

 

Choose ACX service data page in the Gas unit service menu.

2.

 

Connect a tube to the sample out connector and drop its other end into a glass of water.

3.

 

Block the sample inlet, reference flow of the oxygen measuring unit, and the CO

2

 absorber

port that draws room air in. Wait for one minute.

There should be less than 1 bubble per 10 seconds coming out of the tube. Bubble should

not move upwards more than 11 mm per 30 seconds inside the tube. If it does, there is a

leak between the pump and the sample out connector.

4.

 

Perform leak test to the CO

2

 absorber by opening zero valve. The maximum permitted

leakage is the same as above.

CAUTION

 

Do not turn the pump off while performing the leak test. Negative pressure in the

sampling system will suck water in the module.

4.2.2

 

Water separation

1.

 

Dip the patient end of the sampling line into water quickly (about a half second) three times

at 45 seconds' interval. After that drop the end into water and lift it up when the sampling

line is totally filled with water.

2.

 

Check that all the water goes into the trap container and not into the monitor.

4.2.3

 

Steam test for the special tubes

Choose Halothane as anesthetic agent and let the monitor sample room air. Then quickly feed air

of 100 % relative humidity (for instance from a kettle in which you are boiling water) to the monitor.

If the digital reading jumps as much as 0.1 % replace the special (Nafion) tubes.

Summary of Contents for S/5 B-GAS




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands