Datakom DKG-507 User Manual Download Page 9 | Manualshive

Page: 9 / 54

background image

DKG-507 User Manual V-42

(24.05.2013)

- 9 -

Alarms indicate an abnormal situation in the generating set are divided into 3 priority levels:

1-

ALARMS:

These are the most important fault conditions and cause:

-

Therelated

ALARM

led to be on steadily,

-

The genset contactor to be released immediately,

-

The engine to be stopped immediately,

-

The

Horn

,

Alarm

,

Alarm+Load_dump

and

Alarm+LoWarning

digital

outputs to operate, (if selected via programming menu)

2-

LOAD_DUMPS:

These fault conditions cause:

-

Therelated

ALARM

led to be on steadily,

-

The genset contactor to be released immediately,

-

The engine to be stopped after Cooldown period,

-

The

Horn

,

Alarm+Load_dump

and

Alarm+LoWarning

digital outputs to

operate, (if selected via programming menu)

3-

WARNINGS:

These conditions cause:

-

Therelated

ALARM

led to flash,

-

The

Horn

and

Alarm+LoWarning

digital outputs to operate, (if selected

via programming menu)

If the ALARM MUTE button is pressed, the Horn output will be deactivated; however the

existing alarms will persist and disable the operation of the genset.

Alarms operate in a first occurring basis:
-If an alarm is present, following alarms, load_dumps and warnings will not be accepted,
-If a load_dump is present, following load_dumps and warnings will not be accepted,
-If a warning is present, following warnings will not be accepted.

Alarms may be of LATCHING type following programming. For latching alarms, even if the alarm

condition is removed, the alarms will stay on and disable the operation of the genset. The existing

alarms

may be canceled

by pressing one of the operating mode buttons (

LOAD TEST / TEST / OFF / AUTO

).

Most of the alarms have programmable trip levels. See the programming chapter for adjustable

alarm limits.

4. ALARMS AND WARNINGS

«
...
7
8
9
10
11
...
»

Summary of Contents for DKG-507























































Reviews:

No comments

Related manuals for DKG-507

Brand: Bartlett Pages: 30

Brand: Samson Pages: 78

Brand: Rachio Pages: 16

Brand: Ubisys Pages: 2

Brand: Bang & Olufsen Pages: 9

Brand: Bang & Olufsen Pages: 12

Brand: Hach Pages: 86

Brand: C.Nord Pages: 100

CoreBuilder 9000

Brand: 3Com Pages: 78

Brand: B&G Pages: 2

Brand: B&K Pages: 9

Brand: GAUGEMASTER Pages: 2

Brand: EasyIO Pages: 19

Brand: Zero 88 Pages: 2

Brand: Zenit Pages: 24

Brand: J3C Pages: 2

Brand: RadioMaster Pages: 49

SUPERREMOTE UR19A

Brand: X10 Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands