Datakom DKG-507 User Manual Download Page 2 | Manualshive

Page: 2 / 54

background image

DKG-507 User Manual V-42

(24.05.2013)

- 2 -

Section

1. INSTALLATION

1.1. Introduction to the Control Panel
1.2. Mounting the Unit
1.3. Wiring the Unit

2. INPUTS AND OUTPUTS
3. DISPLAYS

3.1. Led Displays
3.2. Digital Displays

4. ALARMS AND WARNINGS
5. MODES OF OPERATION
6. OTHER FEATURES

6.1. Remote start operation

6.2. Sender type selection

6.3. Engine heating operation

6.4. Engine Idle Speed Operation

6.5. Engine Block Heater

6.6. Fuel Pump Control

6.7. Mains Simulation (Disable Start)

6.8. Delayed Mains Simulation, Battery Charging

6.9. Dual Genset Mutual Standby Operation

6.10. Service Request Display

6.11. Engine Hours Meter

6.12. Date-Time Display

6.13. Display of Software Version

6.14. Modem connection

6.15. SMS message sending

6.16. Remote Monitoring and Programming

6.17. Automatic Exerciser

6.18. Resuming to factory set parameters

6.19. Gas engine fuel solenoid control

6.20. Load Shedding / Dummy Load

6.21. Fuel Theft / Fuelling Messages
6.22. Firmware Update

6.23. Changing the Default Engine Speed in Volvo Engines
6.24. Engine Control Mode
6.25. Dual Voltage and Frequency
6.26. Single Phase Operation
6.27. Password Operation (applicable only to DKG-517CAN/MPU)

7. J1939 ENGINE MONITORING AND CONTROL PORT
8. MODBUS COMMUNICATION
9. WEEKLY OPERATION SCHEDULE
10. EVENT LOGGING
11. STATISTICAL COUNTERS
12. MAINTENANCE
13. PROGRAMMING
14. TROUBLESHOOTING
15. DECLARATION OF CONFORMITY
16. TECHNICAL SPECIFICATIONS
17. CONNECTION DIAGRAMS

TABLE OF CONTENTS

«
1
2
3
4
...
»

Summary of Contents for DKG-507























































Reviews:

No comments

Related manuals for DKG-507

Relion 670 series

Brand: ABB Pages: 760

Brand: ABB Pages: 128

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: Value Point Pages: 7

Brand: National Instruments Pages: 31

Brand: National Instruments Pages: 24

Brand: National Instruments Pages: 85

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 98

CompactRIO cRIO-9002

Brand: National Instruments Pages: 21

Brand: National Instruments Pages: 145

Brand: National Instruments Pages: 42

Brand: National Instruments Pages: 8

Brand: National Instruments Pages: 54

Brand: Rain Bird Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands