Datakom DKG-507 User Manual Download Page 8

Page: 8 / 54

DKG-507 User Manual V-42

(24.05.2013)

- 8 -

The unit has 3 seven segment displays. They show:

-Measured parameters,

-Service counters,

-Statistical counters,

-Program parameters.

The navigation between different screens in a group is made with the

MENU

►

button.

Holding the

MENU

►

button pressed for 1 second makes the display to switch to the next group.

VOLTAGE DISPLAY:

This display shows:

-phase R voltage if the load is on mains

-Phase U voltage if the load is on the genset

By pressing the MENU key, below values may be displayed:

-(L1-L2-L3) mains phase to neutral voltages

-(L1-L2-L3) generator phase to neutral voltages

-(L12-L23-L31) mains phase to phase voltages

-(L12-L23-L31) generator phase to phase voltages

If the service counters group is displayed, then this display will show the counter name.
In programming mode it displays (

PGM

CURRENT DISPLAY:

This display will show the current values measured using the current

transformers. Using the programming menu, current transformers within the range of 10/5A to 9000/5A
may be programmed.
In programming mode it displays the program number.

MULTIFUNCTION DISPLAYS:

By pressing the MENU key below values may read:

-generator frequency (Hz)

-generator active power (KW)

-engine rpm

-fuel level

-oil temperature

-battery voltage (V-DC),

In programming mode it displays the program value.

3.2 Digital Displays

Summary of Contents for DKG-507























































Search results

Summary of Contents for DKG-507

Reviews:

Related manuals for DKG-507

Brands by name

Popular brands

Datakom DKG-507, User Manual

Search results

Summary of Contents for DKG-507

Reviews:

Related manuals for DKG-507

Brands by name

Popular brands