Datakom DKG-507 User Manual Download Page 20 | Manualshive

Page: 20 / 54

background image

DKG-507 User Manual V-42

(24.05.2013)

- 20 -

Thanks to its standard serial RS-232 port, the unit offers the remote monitoring and

programming feature.

The remote monitoring and programming PC software is called RAINBOW and may be

downloaded from

www.datakom.com.tr

internet site with

password login

.

The modem, SMS and Modbus modes are not compatible with the local PC connection.

Modem

Enable

,

SMS Enable

and

MODBUS Address

program parameters should be set to 0 before

connection.

The RAINBOW software allows the visualization and recording of all measured parameters.

The recorded parameters may then be analyzed graphically and printed. The software also allows the
programming of the unit and the storage of the program parameters to PC or the downloading of
stored parameters from PC to the unit.

For PCs without a serial port, below USB to serial adapters are tested and approved :

DIGITUS USB 2.0 TO RS-232 ADAPTER (PRODUCT CODE: DA70146 REV 1.1)
DIGITUS USB 1.1 TO RS-232 ADAPTER (PRODUCT CODE: DA70145 REV 1.1)
FLEXY USB 1.1 TO SERIAL ADAPTER (PRODUCT CODE BF-810)
CASECOM USB TO SERIAL CONVERTER (MODEL: RS-01)

The necessary PC connection cable will be supplied by DATAKOM. The cable length should

not be over 3 meters.

6.16 Remote Monitoring and Programming

«
...
18
19
20
21
22
...
»

Summary of Contents for DKG-507























































Reviews:

No comments

Related manuals for DKG-507

Brand: D-Link Pages: 113

Brand: D-Link Pages: 146

Brand: olympia electronics Pages: 10

Brand: Taoglas Pages: 2

Brand: Parker Pages: 4

Brand: Jäger Pages: 18

Cutler-Hammer LMR

Brand: Eaton Pages: 38

Brand: Elotech Pages: 20

Brand: Intermatic Pages: 2

Brand: Rational Pages: 140

Brand: Mitsubishi Pages: 16

Heat Control System

Brand: ORTAL Pages: 20

Brand: EasyCare Pages: 26

Brand: Gioteck Pages: 16

750-652/040-000

Brand: WAGO Pages: 90

Brand: Formula Sound Pages: 6

Brand: Linear Technology Pages: 6

Brand: DSC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands