Datakom DKG-507 User Manual Download Page 32

Page: 32 / 54

DKG-507 User Manual V-42

(24.05.2013)

- 32 -

The program mode is used to program timers, operational limits and the configuration of the unit.

enter the program mode

, hold pressed the

MENU

►

button for 5 seconds.

When the program mode is entered,

the upper display will show “PRGM” and the mid display

will indicate the program parameter number. The lower display will show the parameter value.

If the

PROGRAM LOCK

input is tied to

GROUND

, the program value modification will be

disabled to prevent unauthorized intervention.

It is advised to keep the

PROGRAM LOCK

input tied to

GROUND

The program mode will not affect the operation of the unit. Thus programs may be modified

anytime, even while the genset is running.

Navigation between program parameters is performed via the

MENU

►

button. Holding the

button pressed will cause the program parameter number to increase faster.

Parameter value may be increased and decreased with

▼

and

▲

buttons. If these keys are

held pressed, the program value will be increased/decreased faster.

When a program parameter is modified, it is automatically saved in memory.

MENU

►

button is pressed, next parameter will be displayed.

Program parameters are kept in a non-volatile memory and are not affected from power

failures.

exit the program mode

press one of the mode selection keys. If no button is pressed during 1

minute the program mode will be cancelled automatically.

Program parameters are organized in 2 groups as low and high levels. Entering the program

mode by pressing the

MENU

►

button will allow access to only low level parameters.

In order to access all parameters please hold

OFF

and

MENU

►

buttons pressed.

13. PROGRAMMING

Summary of Contents for DKG-507























































Search results

Summary of Contents for DKG-507

Reviews:

Related manuals for DKG-507

Brands by name

Popular brands

Datakom DKG-507, User Manual

Search results

Summary of Contents for DKG-507

Reviews:

Related manuals for DKG-507

Brands by name

Popular brands