Datakom DKG-507 User Manual Download Page 28

Page: 28 / 54

DKG-507 User Manual V-42

(24.05.2013)

- 28 -

The unit offers the possibility of MODBUS communication via its RS232 serial port.

The connection to the MODBUS master may be done in 3 ways:

1) RS232 connection using directly the RS232 port provided.

2) RS422/485 connection using external RS422/485 converter.

3) Modem connection using external modem.

The MODBUS mode is activated by assigning a controller address to the unit using

MODBUS

Address

program parameter. The possible address range is 1 to 144. Setting the address to 0 will

disable

the MODBUS mode and allow communication under RAINBOW protocol.

The MODBUS properties of the unit are:

-Data transfer mode: RTU

-Serial data: 9600 bps, 8 bit data, no parity, 1 bit stop

-Supported functions:

-Function 3 (Read multiple registers)

-Function 6 (Write single register)

Detailed description about the MODBU

S protocol is found in the document “

Modicon Modbus

Protocol

Reference Guide”

The web address is: www.modbus.org/docs/PI_MBUS_300.pdf

Below is a limited shortlist of readable registers. For the detailed

Modbus Application

Manual

and a complete list of registers please contact DATAKOM.

ADDRESS

(hex)

R /

DATA

SIZE

COEFFICIENT DESCRIPTION

0000

16bit

Mains Phase L1 voltage

0001

16bit

Mains Phase L2 voltage

0002

16bit

Mains Phase L3 voltage

0003

16bit

Genset Phase L1 voltage

0004

16bit

Genset Phase L2 voltage

0005

16bit

Genset Phase L3 voltage

0006

16bit

Genset Phase L1 current

0007

16bit

Genset Phase L2 current

0008

16bit

Genset Phase L3 current

000C

16bit

Mains Phase L12 voltage

000D

16bit

Mains Phase L23 voltage

000E

16bit

Mains Phase L31 voltage

000F

16bit

Genset Phase L12 voltage

0010

16bit

Genset Phase L23 voltage

0011

16bit

Genset Phase L31 voltage

0012

16bit

x10

Mains frequency

0013

16bit

x10

Genset frequency

0016-0017

32bit

x256

Genset active power: this 24 bit signed register holds
the genset active power multiplied by 256. Least
significant 16 bits are in the register 0016h. Most
significant 8 bits are in the LSB of the register 0017h.

0018

8bit

x100

Power factor multiplied by 100 (signed byte). Negative
values indicate a capacitive power factor.

002A

16bit

Engine speed (rpm)

002B

16bit

x10

Oil pressure in bars.

002C

16bit

Coolant temperature in degrees C.

002D

16bit

Fuel level as %

002F

16bit

x10

Battery voltage

003D

8bit

Operating mode
bit_3: manual mode
bit_4: auto mode
bit_5: off mode
bit_6: test mode
bit_7: load test mode

8. MODBUS COMMUNICATION

Summary of Contents for DKG-507























































Search results

Summary of Contents for DKG-507

Reviews:

Related manuals for DKG-507

Brands by name

Popular brands

Datakom DKG-507, User Manual

Search results

Summary of Contents for DKG-507

Reviews:

Related manuals for DKG-507

Brands by name

Popular brands