Datakom DKG-507 User Manual Download Page 5 | Manualshive

Page: 5 / 54

background image

DKG-507 User Manual V-42

(24.05.2013)

- 5 -

RS-232 SERIAL PORT:

This connector provides serial data input and output for various purposes like

remote monitoring and remote programming.

EXTENSION CONNECTOR:

This connector is intended for the connection to output extension modules.

The optional relay extension module provides 8 programmable 16A relay outputs. The unit allows the use
of up to 2 I/O extension modules.

Term Function

Technical data

Description

1

GENERATOR CONTACTOR

Relay output, 16A-AC This output provides energy to the generator

contactor. If the generator phases do not have
acceptable  voltage  or  frequency  values,  the
generator  contactor  will  be  de-energized.  In
order  to  provide  extra  security,  the  normally
closed  contact  of  the  mains  contactor  should
be serially connected to this output.

2

GEN-L1

Generator phase
inputs, 0-300V-AC

Connect the generator phases to these inputs.
The generator phase voltages upper and
lower limits are programmable.

3

GEN-L2

4

GEN-L3

5

GENERATOR NEUTRAL

Input, 0-300V-AC

Neutral terminal for the generator phases.

6

MAINS NEUTRAL

Input, 0-300V-AC

Neutral terminal for the mains phases.

7

MAINS-L3

Mains phase inputs,
0-300V-AC

Connect the mains phases to these inputs.
The mains voltages upper and lower limits are
programmable.

8

MAINS-L2

9

MAINS-L1

10

MAINS CONTACTOR

Relay output, 16A-AC

This  output  provides  energy  to  the  mains
contactor.  If  the  mains  phases  do  not  have
acceptable  voltages,  the  mains  contactor  will
be  de-energized.  In  order  to  provide  extra
security,  the  normally  closed  contact  of  the
generator

contactor

should

be

serially

connected to this output.

11

GROUND

O VDC

Power supply negative connection.

12

BATTERY POSITIVE

+12 or 24VDC

The  positive  terminal  of  the  DC  Supply  shall
be  connected  to  this  terminal.  The  unit
operates  on  both  12V  and  24V  battery
systems.

13

FUEL LEVEL SENDER

Input, 0-5000 ohms

Analogue fuel level sender connection. Do not
connect the sender to other devices. The input
has programmable ohms for VDO senders.

14

OIL PRESSURE SENDER

Input, 0-5000 ohms

Analogue  oil  pressure  sender  connection.  Do
not  connect  the  sender  to  other  devices.  The
input  has  programmable  characteristics  and
connects to any kind of sender.

15

COOLANT TEMP. SENDER

Input, 0-5000 ohms

Analogue

high

temperature

sender

connection.  Do  not  connect  the  sender  to
other  devices.  The  input  has  programmable
characteristics  and  connects  to  any  kind  of
sender.

2. INPUTS AND OUTPUTS

«
...
3
4
5
6
7
...
»

Summary of Contents for DKG-507























































Reviews:

No comments

Related manuals for DKG-507

Brand: Daikin Pages: 2

Brand: Daikin Pages: 12

Brand: Daikin Pages: 12

Brand: Daikin Pages: 46

Brand: Daikin Pages: 21

Brand: Daikin Pages: 20

Brand: Federal Signal Corporation Pages: 79

Brand: Federal Signal Corporation Pages: 32

Brand: Febco Pages: 12

Brand: Game ready Pages: 21

Brand: VAMP Pages: 304

Brand: halstrup-walcher Pages: 39

Brand: Magellan Pages: 44

Brand: Namron Pages: 3

Brand: National Instruments Pages: 31

Brand: National Instruments Pages: 24

Brand: National Instruments Pages: 85

Brand: National Instruments Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands