Datakom D-500 MK3 User Manual Download Page 66

Page: 66 / 197

D-500 MK3 User Manual Firmware V-7.5

- 66 -

Alternator voltage:

0 to 300 V-AC (Ph-N)

Alternator frequency:

0-600 Hz.

Mains (Busbar) voltage:

0 to 300 V-AC (Ph-N)

Mains (Busbar) frequency:

0-600 Hz.

Topology:

1-2-3 phases, with or without neutral

DC Supply Range:

8.0 to 36.0 V-DC.

DC power consumption:

300 mA-DC typical @12V-DC
150 mA-DC typical @24V-DC
600 mA-DC max. @12V-DC
300 mA-DC max. @24V-DC

V-A-cos Accuracy:

0.5% + 1 digit

KW-kVA-kVAr Accuracy:

1.0% + 1 digit

CT Range:

5/5A to 5000/5A

VT Range:

0.1/1 to 6500 / 1

kW Range:

0.1kW to 65000 kW

Current Inputs:

from current transformers. ../5A.

Digital inputs:

input voltage 0 to 36 V-DC.

Analog input range:

0-5000 ohms.

Digital Outputs:

Protected mosfet semiconductor outputs, rated 1Amp@28V-DC

Cranking dropouts:

survives 0V for 100ms.

Magnetic pickup voltage:

0.5 to 30VAC.

Magnetic pickup frequency:

0 to 10000 Hz.

GOV Control Output:

0-10V-DC

AVR Control Output:

±3V-DC, fully isolated

Charge Alternator Excitation:

2W.

Display Screen:

2.9

”, 128x64 pixels

Ethernet Port:

100 Mbits

USB Device:

USB 2.0 Full speed

USB Host:

USB 2.0 Full speed

RS-485 Port:

selectable baud rate

Data Link Port:

Fully Isolated CANBUS

Operating temperature:

20°C to 70°C (-4 to +158 °F)

Storage temperature:

40°C to 80°C (-40 to +176°F)

Maximum humidity:

95% non-condensing.

IP Protection:

IP54 from front panel, IP30 from the rear.

Dimensions:

200 x 148 x 46mm (WxHxD)

Panel Cut-out Dimensions:

176 x 121 mm minimum.

Weight: -----
Case Material:

High Temperature, non-flammable ABS/PC

Mounting:

Front panel mounted with rear retaining plastic brackets.

EU Directives Conformity

-2014/35/EC (low voltage)
-2014/30/EC (electro-magnetic compatibility)

Norms of reference:

EN 61010 (safety requirements)
EN 61326 (EMC requirements)

UL / CSA Conformity:

UL 6200, Controls for Stationary Engine Driven Assemblies (Certificate # - 20140725-E314374)

CSA Compatibility:

-CAN/CSA C22.2 No. 14-13

– Industrial Control Equipment

9. TECHNICAL SPECIFICATIONS

Summary of Contents for D-500 MK3






































































































































































































Search results

Summary of Contents for D-500 MK3

Reviews:

Related manuals for D-500 MK3

Brands by name

Popular brands

Datakom D-500 MK3, User Manual

Search results

Summary of Contents for D-500 MK3

Reviews:

Related manuals for D-500 MK3

Brands by name

Popular brands