manualshive.com logo in svg

Danfoss VLT 5000, Operating Instructions Manual, Page: 54 / 88

Share
Download
Danfoss VLT 5000 Operating Instructions Manual Download Page 54

Synchronizing controller 

 
 

 
MG.10.N4.02 - VLT is a registered Danfoss trademark 

 53 

Setting the parameters 

 

For this we recommend you to have the description of parameters at hand. See the VLT 
5000/VLT5000Flux Operating Instructions. 

NOTE: It is very important that the VLT is optimized for the motor before optimizing the Synchronizing 
controller. First you record the motor data and perform an AMA (Automatic Motor Adaptation) if 
possible and then you can start programming your synchronization functions 

 
Parameter 205  Maximum reference: Set the frequency for a value that is about 10% higher 

than the maximum value of parameter 716. 

 

Example: 
Motor 7.5kW, 1460 

1

/

min

 at 50Hz, speed of the application approx. 1800 

1

/

min 

 

1

,

1

*

*

Nom

n

Applicatio

Nom

N

N

f

 = 

50

1800

1460

11

1

1

Hz *

* ,

min

min

= 62Hz Maximum ref. value 

 
Parameter 221  Torque limit for motor mode: Set for maximum. – Choose a lower value, if 

special safety precautions are necessary. 

 
Parameter 222  Torque limit for regenerative operation: Set for maximum. – Choose a lower 

value, if special safety precautions are necessary. 

 
Parameter 223  Set the minimum current that is to activate the brake. Choose a value that is 

below the motor magnetisation current. 

 
Parameter 701 

Record “1” to start the test program. 

 
Parameter 709  When performing position synchronization this parameter is used to insert a 

filter to compensate for an oscillating master signal. If, for example, the master 
is experiencing shock loads the pid loop of the synchronizing controller will 
have a tendency to oscillate as well. A negative value must be entered.  

 
 

Example: 

 

If a filter factor of –100000 (100 ms) is used the correction is balanced within: 

 

1000/(filter factor *10)= 1 second.  

 

 

Parameter 711 

Record the slave encoder type. “0” represents the incremental encoder. 

 
Parameter 712 

Record the resolution of the slave encoder. 

 
Parameter 713 

Record the master encoder type. “0” represents the incremental encoder. 

 
Parameter 714 

Record the resolution of the master encoder. 

 
Parameter 715  Record “1” for clockwise rotation of both master and slave. Record “-1” if the 

slave is to run in the opposite direction. 

 
Parameter 716 

Record maximum RPM measured at the slave encoder. 

 
Parameter 717  Minimum ramp: Set the time in ms for the slave drive to accelerate from 

standstill to maximum speed (par 716). The value is important, as this setting 
highly affects the control accuracy! 

Summary of Contents for VLT 5000

























































































Reviews:

No comments