Danfoss VLT 5000 Operating Instructions Manual Download Page 23

Page: 23 / 88

Synchronizing controller

MG.10.N4.02 - VLT is a registered Danfoss trademark

Description of parameters

Parameter

number

Description

701

Selection of the operation mode: “1“ - test run; “2“ - synchronization

702

P-portion of the Synchronizing controller. Setting: see Examples.

703

D-portion of the Synchronizing controller. Setting: see Examples.

704

I-portion of the Synchronizing controller. Setting: see Examples.

705

Limitation for I-portion. Setting: see Examples.

706

Band width for PID controller

707

Velocity feed forward. Setting: see Examples.

708

Acceleration feed forward. Setting: see Examples.

709

Velocity filter

710

Store data: Here you can save the selected data permanently in the EEPROM.

0 =

function,

= data are being saved. While saving continues, the value remains “1“; when

saving is finished, the value automatically reverts to “0“. Similarly, during saving,
Output O5 “Saving“ is set to “1“. Saving is not possible during operation, but only
in the disengaged, stopped state.

711

Slave encoder type:

Setting range:

= Incremental encoder.

= Absolute encoder with 262kHz clock frequency,

= Absolute encoder with 105kHz clock frequency.

100  =  as “0” but with hardware monitor active.
101  =  as “1” but with hardware monitor active.
102  =  as “2” but with hardware monitor active.

712

Slave encoder resolution in increments per rotation.

713

Master encoder type:

Setting range:

0 =

Incremental

encoder.

= Absolute encoder with 262kHz clock frequency,

= Absolute encoder with 105kHz clock frequency.

100  =  as “0” but with hardware monitor active.
101  =  as “1” but with hardware monitor active.
102  =  as “2” but with hardware monitor active.

714

Master encoder resolution in increments per rotation.

Summary of Contents for VLT 5000

























































































Search results

Summary of Contents for VLT 5000

Reviews:

Danfoss VLT 5000, Operating Instructions Manual, Page: 23 / 88

Search results

Summary of Contents for VLT 5000

Reviews: