manualshive.com logo in svg

Danfoss VLT 5000, Operating Instructions Manual, Page: 16 / 88

Share
Download
Danfoss VLT 5000 Operating Instructions Manual Download Page 16

Synchronizing controller 

 
 

 
MG.10.N4.02 - VLT is a registered Danfoss trademark 

 15 

Description of terminals 

I/O # 

Designation 

Description 

12

 

24V DC 

24V power supply for switches etc. maximum load: see page 8 

13

 

24V DC 

24V power supply for switches etc. maximum load: see page 8 

16

 

Gear ratio 2

1

 

Synchronous operation; Program 2:  

Gear ratio most significant bit 

17

 

Gear ratio 2

0

 

Synchronous operation; Program 2: 

Gear ratio least significant bit 

18

 

Not used 

  

19

 

Home run 

Synchronous operation; Program 2: 

Starts the homing. 

20

 

GND 

Ground for 24V, normally bridged with Terminal 39, but this can 
be set to “OFF” by means of Switch SW4 on the control card. 

27

 

Reset/Enable 

Error reset on rising edge. To enable operation, this input must be 
switched to “1”. “0” = motor coast. 

29

 

Hold 

Synchronous operation; Program 2: 

The drive is held at a programmable, or the present speed. 
Synchronous control is not activated. 

32

 

Test run reverse 

 

Speed/Pos – 

Test run; Program 1:  

Test run reverse at the speed defined in Parameter 725 

Synchronous operation; Program 2:  

In velocity synchronous mode (P. 725 = 0, 1, 6 or 7) the gear ratio 
and thus the velocity of the slave can be changed by the value 
specified in parameter 744. 

In position synchronous and marker synchronous operation (P. 
725 = 1, 2, 4 or 5), the position offset of the slave can be changed 
by the value specified in Parameter 744. The sign of the value in 
parameter 744 selects the offset type to be absolute or relative. 

Absolute offset means that the fixed offset of parameter 742 is 
changed and this offset is executed when restarting 
synchronization. 

Relative offset means that the actual slave position is displaced 
but the fixed offset of parameter 742 is unchanged. This again 
means that the actual slave position is maintained when restarting 
synchronization. Relative offset is useful when always changing 
the offset in the same direction as this would give a very high 
fixed offset when using absolute offset. This high fixed offset 
would then be executed when restarting synchronization and the 
min. or max. limit of parameter 742 would eventually be reached.  

Summary of Contents for VLT 5000

























































































Reviews:

No comments