Dalsa Xtium-CL MX4 User Manual Download Page 94

Page: 94 / 136

•

Technical Specifications

Xtium-CL MX4 User's Manual

Status LED Functional Description

D1 Boot-up/PCIe status LED

Color

State

Description

Red

Solid

FPGA firmware not loaded

Green

Solid

Normal FPGA firmware loaded, Gen2 speed, link width x4

Green

Flashing

Normal FPGA firmware loaded, Gen1 speed, link width x4

Solid

Normal FPGA firmware loaded, Gen2 speed, link width not x4

Flashing

Normal FPGA firmware loaded, Gen1 speed, link width not x4

Blue

Solid

Safe FPGA firmware loaded, Gen2 speed

Blue

Flashing

Safe FPGA firmware loaded, Gen1 speed

Red

Flashing

PCIe Training Issue – Board will not be detected by computer

Camera Link LEDs
(D4 = Camera Link connector #1, D3 = Camera Link connector #2)

Color

State

Description

Red

Solid

No Camera Link pixel clock detected

Green

Solid

Camera Link pixel clock detected. No line valid detected.

Note: for D3, when configuring for Full Camera Link, both pixel clock on

the 2

cable must be detected.

Green

Slow Flashing

~1 Hz

Camera Link pixel clock and line valid signal detected

Note: for D3, when configuring for Full Camera Link, both line valid on

the 2

cable must be detected.

Green

Fast Flashing

~8 Hz

Acquisition in progress



Notes 1: When using a Full configuration, if the input on CL1 is configured as Camera Link

Base, the D3 (for CL2) will remain RED at all times.



Note 2: LED D3 and D4 are independent.



Note 3: Full FPGA defaults to Camera Link Medium configuration.



Note 4: For a Pixel Clock and Line Valid to be detected, the following rules apply:

•

CL1: Requires 1 clock and 1 LVAL

•

CL2: Camera Link Base configuration: N/A

•

CL2: Camera Link Medium configuration requires 1 clock and 1 LVAL

•

CL2: Camera Link Full/80-bit configurations requires 2 clocks and 2 LVAL

Summary of Contents for Xtium-CL MX4









































































































































Search results

Summary of Contents for Xtium-CL MX4

Reviews:

Related manuals for Xtium-CL MX4

Brands by name

Popular brands

Dalsa Xtium-CL MX4, User Manual

Search results

Summary of Contents for Xtium-CL MX4

Reviews:

Related manuals for Xtium-CL MX4

Brands by name

Popular brands