Dahua DH-PFR5QI-E60 User Manual Download Page 62

Page: 62 / 113

User’s Manual

● Unauthorized mode: The SD card authorized by other devices shows unauthorized mode.

The SD cards of this status do not support operations of setting read only, read & write,

formatting and encryption.

● Encrypted mode: The SD cards encrypted and authorized on this camera show encrypted

mode. The camera can record max. 10 pieces of encrypted SD information. When the

recorded videos exceed 10 pieces, the earliest ones will be overwritten.

● Functions might vary with different models, and the actual product shall prevail.

● If you enter the wrong password for five times when authorizing, modifying, and clearing

password, the camera will be locked for five minutes.

● Make sure that the SD card has been authorized before recording and playback.

● The health status of SD card:

◇

Green: The health status is excellent.

◇

Blue: The health status is good.

◇

Orange: The health status is moderate.

◇

Red: The health status is poor, and you need to replace the SD card.

Select

Setting > Storage > Destination >

Local

, and then the

Local

interface is

displayed. See Figure 3-54.

Select the SD card.



Click

Read Only

, and then the SD card is set to read only.



Click

Read & Write

, and then the SD card is set to read & write.



Click

Hot Swap

, and then you can pull out the SD card.



Click

Refresh

, and then you can format the SD card.



Click

Format

, and you can format the SD card.

Local

3.5.3.3

FTP

FTP function can be enabled only when it was selected as a destination path. When the network

does not work, you can save all the files to the internal SD card for emergency.

Step 1 Select

Setting > Storage > Destination > FTP

Summary of Contents for DH-PFR5QI-E60


















































































































Search results

Summary of Contents for DH-PFR5QI-E60

Reviews:

Related manuals for DH-PFR5QI-E60

Brands by name

Popular brands

Dahua DH-PFR5QI-E60, User Manual

Search results

Summary of Contents for DH-PFR5QI-E60

Reviews:

Related manuals for DH-PFR5QI-E60

Brands by name

Popular brands