background image

WARRANTY

D.A.C.E. warrants the 

original

purchaser, at the point of sale, that the product is in good working order and is free from any 

defect. 

ANY

warranty claim 

must

be accompanied by the 

original 

invoice. 

The original purchaser is responsible for checking that the equipment is free from any visible defect before it leaves the point of 
sale. 
The warranty period is 

24 months 

from 

date of MANUFACTURE

.

The warranty is a 

“walk in 

“ warranty. No warranty claim will be entered into “on site”. 

The equipment must be returned to the factory with the original invoice for any repair or  
replacement. The 

transport

 cost is for the end 

users account

.

If the equipment was purchased at a dealer, merchant or agent of D.A.C.E. the claim must be directed to said merchant, dealer 
etc. 
The warranty will 

not cover 

any of the following circumstances in any way. 

1.  Incorrect installation of the equipment. 
2.  Incorrect wiring of the equipment. 

3.

Lightning, flooding, power-surge, fire or any form of abnormal use of the 

equipment

.

SPECIFICATIONS

Max gate mass—500 kg 
Max gate length—8m 
Max number of operations per day— 80 if start up is less than 6 kg 
Max start up force—10 kg 
Electric motor—120 w 12v dc 
Over-current sensing—electronic 
Auxiliary out-put—12v DC 
Gate speed—20 m per minute, dependant on gate mass. 
Charge rate—13.8 vDC 
Receiver— onboard- maximum 30 remotes. 
Transformer—plug in type, 220vAC ~ 16vAC 
Auxiliary wiring—pluggable. 

Optional features

Pedestrian opening. 
Infra-red safety beams 
Loop detector compatible  
Theft deterrent bracket 

Note

this gate operator is designed to be used in a 

domestic application only

. If the application  

requires a higher number of operations D.A.C.E. suggest that a DuraSlide AC/ DC  or 500 SERIES type motor is used. 

CONNECTING AN EXTERNAL L.E.D. (OPTIONAL)

An external L.E.D. (light emitting diode) can be wired  to the motor in order to indicate the status of the gate at all times. The 
most common place to set the L.E.D. is in the handset of the intercom. If there is no intercom then the L.E.D. can be placed in any 
chosen location.  
The L.E.D. indications are as follows. 
Gate open …………….L.E.D. ON SOLID. 
Gate closed …………..L.E.D.  FLASH ONCE EVERY TWO SECONDS. (If mains is on) 
Gate moving ………….L.E.D. FLASHING CONTINUOUSLY  
If the gate is closed and there is no L.E.D. indication, this means that the mains power is not on and the battery is not charging, 
this means that the battery will go flat and the motor will operate until the battery is flat.

L.E.D. 

Summary of Contents for Compact























Reviews: