background image

 5

 

GENERAL OVERVIEW 

 
This manual covers the following phototherapy equipment: 
 
  

UV Series 

  

7 Series 

  

2 Series 

  

M Series 

  

1 Series 

   

 

 
Your device may be equipped with a variety of different lamps and may be manufactured to a number 
of different electrical specifications to meet national and international standards. It may also be 
equipped with either a Flex™ integrating dosimetry control or a Flex timer control.  And, in either case, 
your physician may have prescribed your device with the FlexRx system that limits the total number of 
exposures that the device will deliver.  This manual is applicable for all lamp configurations, electrical 
specifications and control types.  
 
This section of the manual, the 

General Overview, 

covers topics such as site location, the initial 

inspection of the device, lamp type confirmation, eye protection, precautions and phototherapy in 
general.    These topics are common to all devices.    
 
Beginning on page eight (8) you will find 

Device Specific Information

 on the UV, 7, 2, M, and 1 

Series devices.   
 
The next section, beginning on page sixteen (16), 

Flex Operating Instructions 

provides operating 

instructions for all devices.  
 
Finally, the last section, 

Care of Your Unit, 

beginning on page twenty-three (23), contains information 

concerning the maintenance, cleaning, re-lamping, and calibration (where applicable) of your device 
along with warranty and service contact details. 
 
We suggest that you first read the sections concerning site selection and general inspection under 

Overview 

and then the instructions that are 

Specific

 to your device with regard to unpacking and 

assembly. 
 
When you first receive the device: 

Inspect the box  

Any signs of shipping damage should be noted on the shipping receipt that you will be asked to sign 
by the delivering carrier.  If damage is discovered after unpacking the unit, save all packing materials 
and call Daavlin at 1-800-322-8546 for inspection and repair.   

            The delivering carrier must be notified of any shipping damage within twenty-four (24) hours 

   

 to protect your right to an insurance claim. 

Locate the following materials 

 

 

   Time chart     

    Power Output Certificate   

   Protective Eyewear   

 

   Manual  

 
 

Summary of Contents for 7 Series




























Reviews: