D-Link DGS-3312SR Product Manual Download

Page: 88 / 244

DGS-3312SR Gigabit Layer 3 Switch

MAC Notification Port Settings

Enable or disable MAC notification for ports with the window below.

Figure 4- 42. MAC Notification Port Settings window

The following parameters can be set:

Parameter

Description

Unit

Allows you to specify a Switch in a Switch stack using that Switch’s Unit ID. Number
15 indicates a Switch in standalone mode.

From/To

A consecutive group of ports may be configured starting with the selected port.

State

This pull-down menu allows you to enable or disable MAC notification for the
specified Switch and group of ports.

System Log Server

Use the System Log to keep a record of warning and other pertinent system information.

The Switch can send system log (SysLog) messages to up to four designated servers.

Summary of Contents for DGS-3312SR





















































































































































































































































Search results

Summary of Contents for DGS-3312SR

Reviews:

Related manuals for DGS-3312SR

Brands by name

Popular brands

D-Link DGS-3312SR, Product Manual

Search results

Summary of Contents for DGS-3312SR

Reviews:

Related manuals for DGS-3312SR

Brands by name

Popular brands