manualshive.com logo in svg

D-Link DGS-3312SR, Product Manual

Share
Download
D-Link DGS-3312SR Product Manual Download Page 118

DGS-3312SR Gigabit Layer 3 Switch 

Link-State Advertisement Header

Link-State Age

Options

Link-State Type

Link-State ID

Advertising Router

Link-State Sequence Number

Link-State Checksum

Length

 

Figure 5- 14. Link-State Advertisement Header 

Field Description 

Link State Age 

The time is seconds since the link state advertisement was 
originated. 

Options 

The optional capabilities supported by the described portion of 
the routing domain. 

Link State Type 

The type of the link state advertisement. Each link state type has 
a separate advertisement format. The link state type are as 
follows: 
Type      Description 
1            Router Links 
Network Links 
Summary Link (IP Network) 
Summary Link (ASBR) 
AS External Link 

Link State ID 

This field identifies the portion of the internet environment that is 
being described by the advertisement. The contents of this field 
depend on the advertisement’s Link State Type. 

Advertising Router 

The Router ID of the router that originated the Link State 
Advertisement. For example, in network links advertisements this 
field is set to the Router ID of the network’s Designated Router. 

Link State Sequence 
Number 

Detects old or duplicate link state advertisements. Successive 
instances of a link state advertisement are given successive Link 
State Sequence numbers. 

Link State Checksum 

The Fletcher checksum of the complete contents of the link state 
advertisement, including the link state advertisement header by 
excepting the Link State Age field. 

Length 

The length in bytes of the link state advertisement. This includes 
the 20-byte link state advertisement header. 

 

105 

Summary of Contents for DGS-3312SR





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands