manualshive.com logo in svg

D-Link DGS-3312SR, Product Manual

Share
Download
D-Link DGS-3312SR Product Manual Download Page 127

DGS-3312SR Gigabit Layer 3 Switch 

 

Figure 5- 26. RIP Global Setting window 

RIP Interface Settings 

RIP settings are configured for each IP interface on the Switch. Click the 

RIP Interface Settings

 link in the 

RIP

 sub-

folder. The window appears in table form listing settings for IP interfaces currently on the Switch. To configure RIP 
settings for an individual interface, click on the hyperlinked name of the interface. 

 

Figure 5- 27. RIP Interface Settings window 

Click the name of the interface you want to setup for RIP to the following window: 

 

Figure 5- 28. RIP Interface Settings – Edit window 

Refer to the table below for a description of the available parameters for RIP interface settings. To return to the RIP 
Interface Settings table, click the Show All RIP Interface Settings link. 

The following RIP settings can be applied to each IP interface: 

 Parameter 

Description 

Interface Name 

The name of the IP interface on which RIP is to be setup. This interface must be 
previously configured on the Switch. 

TX Mode <

Disabled

> 

Toggle among 

Disabled

, 

V1 Only

, 

V1 Compatible

, and 

V2 Only

. This entry specifies 

which version of the RIP protocol will be used to transmit RIP packets. 

Disabled

 

prevents the transmission of RIP packets. 

114 

Summary of Contents for DGS-3312SR





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands