manualshive.com logo in svg

D-Link DGS-3312SR, Product Manual

Share
Download
D-Link DGS-3312SR Product Manual Download Page 194

DGS-3312SR Gigabit Layer 3 Switch 

1024-1518 

The total number of packets (including bad packets) received that were between 
1024 and 1518 octets in length inclusive (excluding framing bits but including FCS 
octets). 

Time Interval

 

<

1s

>

 

The time between updates received from the Switch, in seconds. The default is 

1s

. 

Record Number 
<

200

> 

Select number of times the Switch will be polled between 

20

 and 

200

. The default 

value is 

200.

 

Show/Hide 

Check whether or not to display 64, 65-127, 128-255, 256-511, 512-1023, and 1024-
1518 packets received. 

MAC Address  

This allows the Switch’s dynamic MAC address forwarding table to be viewed. When the Switch learns an association 
between a MAC address and a port number, it makes an entry into its forwarding table. These entries are then used to 
forward packets through the Switch. 

181 

Summary of Contents for DGS-3312SR





















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands